No Login Data Private Local Save

Aquarium Fishless Cycle Ammonia Calculator – Online Dose

6
0
0
0

Aquarium Fishless Cycle Ammonia Calculator

Calculate the exact ammonia dose needed for your fishless cycling setup. Supports household ammonia, Dr. Tim's, and custom concentrations.

Aquarium Volume
gal
Quick Select (Gallons):
Quick Select (Liters):
Ammonia Settings
3.0
1 ppm2345 ppm
Recommended: 3–4 ppm for most freshwater tanks
Safety: Use only pure ammonia without surfactants, dyes, or perfumes. Work in a ventilated area.
Recommended Dose
1.14 mL
23 drops ≈ 0.23 tsp
Use a syringe or graduated dropper for precise measurement. 1 mL ≈ 20 drops.
Quick Cycling Guide
1
Dose Ammonia

Add the calculated amount to reach 3–4 ppm. Record the exact dose.

2
Test Daily

Monitor ammonia, nitrite, and nitrate levels. Ammonia will drop as bacteria grow.

3
Re-dose & Complete

When ammonia drops near 0, re-dose to 2–3 ppm. Cycle is complete when ammonia & nitrite reach 0 within 24 hours.

Pro Tip: Keep water temperature at 80–84°F (27–29°C) and ensure good aeration during cycling for fastest bacterial growth.
Frequently Asked Questions

A fishless cycle is the process of establishing the nitrogen cycle in a new aquarium without using live fish. Instead, you add pure ammonia directly to the water to feed beneficial bacteria. This calculator helps you determine the exact ammonia dose based on your tank size, target concentration, and the ammonia product you're using — preventing under-dosing (which slows cycling) or over-dosing (which can stall the cycle or harm future inhabitants).

For most freshwater aquariums, a target of 3–4 ppm (mg/L) is ideal. This provides enough food for nitrifying bacteria without risking a stalled cycle. Levels above 5 ppm can inhibit the growth of nitrite-oxidizing bacteria and slow the cycling process. For sensitive setups (e.g., shrimp tanks), some aquarists prefer 2 ppm. Our calculator defaults to 3 ppm as a safe, effective starting point.

You must use pure ammonia without additives. The most commonly recommended product is Ace Hardware Janitorial Strength Ammonia (10% ammonium hydroxide). Avoid any ammonia containing surfactants, dyes, perfumes, or cleaning agents — these are toxic to aquatic life. To test: shake the bottle; pure ammonia will produce minimal foam and dissipate quickly. Dr. Tim's Ammonium Chloride is a commercial alternative specifically formulated for fishless cycling.

For nano tanks (under 5 gallons), the required dose is often less than 0.5 mL. Use a 1 mL syringe with 0.1 mL graduations (available at pharmacies) or count drops (approximately 20 drops = 1 mL). Our calculator displays both mL and drops so you can choose the most practical method. For extreme precision with nano tanks, diluting the ammonia with distilled water at a known ratio can make measuring easier.

Initial dose: Add ammonia once to reach your target level (3–4 ppm). Then test daily. When ammonia drops below 0.5 ppm (usually after 3–7 days for the first drop), re-dose back to your target. As the cycle progresses, ammonia will be consumed faster. You may need to re-dose every 1–2 days. The cycle is complete when the tank can process 2–3 ppm of ammonia to 0 ppm ammonia and 0 ppm nitrite within 24 hours.

If ammonia levels exceed 5–6 ppm, the cycling process can stall because high ammonia concentrations inhibit nitrite-oxidizing bacteria. If you've overdosed, perform a partial water change (25–50%) to bring levels back down to 3–4 ppm, then continue as normal. Always double-check your calculation using our tool before dosing — it's much easier to add a little more than to remove excess.

A fishless cycle typically takes 4–6 weeks, though it can range from 3 to 8 weeks depending on water temperature, pH, aeration, and whether you use bottled bacteria starters. Warmer water (80–84°F / 27–29°C) and good oxygenation speed up the process. Adding a beneficial bacteria supplement (like FritzZyme or Dr. Tim's One & Only) can reduce cycling time to as little as 1–2 weeks.

Yes, the same calculation principles apply. However, for saltwater fishless cycling, many aquarists target a slightly lower ammonia level of 2–3 ppm. Marine nitrifying bacteria can be more sensitive to high ammonia. Select 2 or 3 ppm on the slider, and the calculator will provide the correct marine-safe dose. Dr. Tim's Ammonium Chloride is especially popular in the reef-keeping community for this purpose.

Commercial products like Dr. Tim's often provide simplified dosing (e.g., "4 drops per gallon for 2 ppm"). Our calculator uses the exact mathematical relationship between tank volume, desired ppm, and ammonia concentration. Slight differences may arise because: (1) drop sizes vary between droppers, (2) manufacturers round for convenience, and (3) our calculator accounts for the precise concentration. For Dr. Tim's, we use an effective concentration of ~3.8% based on their stated 4 drops/gallon = 2 ppm guideline.

A healthy fishless cycle follows this pattern: Stage 1: Ammonia begins dropping as ammonia-oxidizing bacteria (Nitrosomonas) colonize — you'll see nitrite rising. Stage 2: Nitrite peaks then falls as nitrite-oxidizing bacteria (Nitrobacter/Nitrospira) establish, while nitrate accumulates. Stage 3 (Complete): The tank processes 2–3 ppm ammonia to 0 ammonia + 0 nitrite within 24 hours. Water may become slightly cloudy during bacterial blooms — this is normal and clears on its own. Consistent testing with a liquid test kit (not strips) is essential.
🔧 Related Tools